Jetson Customize Pcie

Customize PCIe (per-controller status / lanes / speed)

Overview

PCIe on Tegra264 (Thor, [email protected]) and Tegra234 (Orin, [email protected]) is split across multiple controllers that share the UPHY lane pool with USB3 / MGBE / UFS. Each controller's runtime behavior is determined by two surfaces, both required:

Skipping the kernel overlay on a disable lets the kernel probe a powered-down PHY (link timeouts in dmesg). Skipping the ODMDATA token on a disable leaves BPMP holding the PHY hot.

Agentic, not table-driven — no controller table, no questions.json. Every controller, lane width, schematic-routed receptacle, and authoritative DT node address is discovered at runtime from the docs + DTB + carrier pinmap.

The output is a kernel-DT overlay commit only. Per-controller fragment@N blocks are appended to the composite custom overlay .dts per ../​../​references/​bsp-customization-kernel-dtb.md and committed to the bsp_sources/ hardware repo. /​jetson-build-source compiles the composite to .dtbo and owns its Makefile + flash-conf registration.

This skill MUST NOT edit ODMDATA="...". All ODMDATA tokens (pcie@N_status=…, pcie@N_max-link-speed, pcie@N_pcie-mode, pcie@N_clk-scheme, pcie-cN-endpoint-enable, plus the uphyX-config-N surface tokens and UPHY_CONFIG="" clear) are emitted by /​jetson-customize-uphy in a single atomic commit on the carrier flash-conf fork. The allocation table this skill consumes from the UPHY sidecar already tells the operator which controllers are okay / disabled / per-lane sized; this skill only translates that table into kernel-DT overlay fragments and verifies that the overlay agrees with the ODMDATA already committed by customize-uphy (consistency check in Step 8 — disagreement is reported, not silently fixed).

When to invoke

• The user says "configure PCIe", "enable PCIe controller", "set PCIe num-lanes", "change PCIe link speed", or asks to flip a pcie@N_status token.
• A specific PCIe slot or M.2 receptacle doesn't enumerate after flash, OR the link trains at the wrong width / speed.
• jetson-customize-uphy ran and re-allocated lanes across PCIe controllers (e.g. switched from uphy0-config-7 to uphy0-config-6 enabling PCIe C3); the per-controller side now needs to be brought up.
• jetson-customize-mgbe reports the QSFP path is wired but the kernel doesn't probe its PCIe-side companion (rare; XFI configurations).

Prerequisites:

• Active profile with reference_devkit: + custom_carrier: blocks.
• <source.root_path>/​Linux_for_Tegra/​.git exists (/​jetson-init-source).
• /​jetson-derive-carrier has run — carrier flash-conf fork is in the overlay tracker.
• /​jetson-customize-uphy has run — its JSON sidecar at <workspace>/​target-platform/<profile-stem>.jetson-customize-uphy.json drives the per-controller enable decision.
• Source-of-truth docs registered or supplied at prompt: Adaptation Guide, Module Design Guide, SoC TRM.
• When custom_carrier: is present, both documents.custom_carrier_schematic AND documents.custom_carrier_pinmux_xls are REQUIRED. Refuse the run if either is missing — routing on a custom carrier cannot be guessed. Reference-devkit-only profiles skip this check.
• dtc on PATH.

Procedure (summary)

Full step-by-step walkthrough lives in references/​procedure.md. High-level flow:

1. Resolve active target + open source-of-truth documents (incl. <carrier-pinmap>, <ref-dtb>, <uphy-state>). Refuse if <uphy-state> is missing.
2. Diff PCIe topology — devkit vs custom carrier — by decompiling <ref-dtb> and grepping the schematic for PEX<N>_* net labels.
3. AskUserQuestion (multiSelect) — which controllers to customize.
4. Per-controller verification: pinmap + schematic + pin_verifier.py for PE<N>_CLKREQ_L, PE<N>_RST_L, optional PE<N>_WAKE_L.
5. Auto-derive per-controller plan (enable from <uphy-state>, lanes / speed from Adaptation Guide, mode hard-pinned to "rc") → mandatory confirm-or-customize gate.
6. Append per-controller fragment@N blocks (marker /​* custom-bsp: pcie:pcie@<addr> */) to the composite custom overlay .dts in bsp_sources/. Pre-flight dtc + fdtoverlay. Commit via the workflow's preview gate. Do not edit ODMDATA — /​jetson-customize-uphy already emitted pcie@N_status=…, pcie@N_max-link-speed, pcie@N_pcie-mode, pcie@N_clk-scheme, and pcie-cN-endpoint-enable in its single atomic ODMDATA commit. This skill only translates the per-controller plan into kernel-DT overlay fragments.
7. (Step folded into Step 6 — overlay-only emission.)
8. Cross-check ODMDATA vs overlay consistency. On a contradictory row, stop and ask the user how to recover the two commits. Never run git reset --hard autonomously.
9. Write run-state JSON sidecar at <workspace>/​target-platform/<profile-stem>.jetson-customize-pcie.json
   • summary, then drive the downstream next-step chain via sequential AskUserQuestion prompts per references/​procedure.md Step 9. Never substitute a printed "Next step: …" line for the prompts.

Limitations

• Mode hard-pinned to RC. Endpoint mode is only emitted when the operator passes mode_override="ep" in Step 5c.
• enable is derived, not asked. UPHY-allocated controllers are mandatorily okay; non-allocated are mandatorily disabled.
• No upstream BSP edits. Output lands in Linux_for_Tegra/ + bsp_sources/ only.
• Pre-flight overlay merge is a sanity check, not the production build. /​jetson-build-source is authoritative.
• Flash-conf overlay registration is out of scope. Owned by /​jetson-build-source Step 5.0a.

Troubleshooting

• <uphy-state> missing → run /​jetson-customize-uphy first.
• Slot doesn't enumerate after flash → check dmesg | grep pcie; re-verify ODMDATA pcie@<N>_status=okay and the overlay fragment agree (Step 8 table in references/​procedure.md).
• Link trains at wrong width → confirm UPHY config in <uphy-state> allocates the expected lane count; the kernel fragment's num-lanes must match.
• compatible mismatch → fix the composite root, not the fragment. UEFI plugin-manager silently skips on mismatch.
• Contradictory ODMDATA-vs-overlay row → ask the user; do not auto-git reset --hard. See gotchas.
• Common pitfalls — see references/​gotchas.md (RC pinning, node- address sourcing, stock-disabled controllers, intra-file handoff with jetson-customize-uphy).

References

• references/​procedure.md — full nine- step procedure (topology diff, plan derivation, overlay append, ODMDATA cross-check, sidecar).
• references/​gotchas.md — failure modes
  • invariants (RC pinning, address sourcing, BPMP handoff).
• ../​../​scripts/​pin_verifier.py — shared HSIO pin verifier (Step 4).
• ../​../​references/​platform_template.yaml — documents: block consumed by Step 1.
• ../​../​context/​bsp-customization-workflow.md — overlay edit protocol + commit message preview gate.
• ../​../​references/​bsp-customization-kernel-dtb.md — composite overlay filename / skeleton / append protocol.
• ../​jetson-customize-uphy/​SKILL.md — sibling skill that owns UPHY lane allocation; its sidecar drives the per-controller enable decision.
• ../​jetson-customize-pinmux/​SKILL.md — sibling skill invoked by Step 4 (with operator confirmation) to fix HSIO pin SFIO mismatches.
• ../​jetson-customize-mgbe/​SKILL.md — sibling for MGBE controllers; shares the two-surface (ODMDATA
  • overlay) pattern.
• ../​jetson-derive-carrier/​SKILL.md — must run first; produces the carrier flash-conf fork edited in Step 6.
• ../​jetson-init-source/​SKILL.md — produces the overlay tracker + bsp_sources repo this skill commits into.